MAGLOC®
1. Tactical
Recoil Control Thumb Rest for S&W M&P
in 9mm, 40 S&W and 45 ACP cal. US$21.00
(Does not
fit S&W M&P M2.0)
Features:
1. Reduces
muzzle jump by 40 to 70%.
2. Improves shooting speed & accuracy.
3. Ambidextrous - fits for left or right hand shooter.
4. Prevents thumb from touching slide.
5. Avoids "slide cuts" on web of shooting hand.
6. No modification required.
Specification:
1.
Made of glass fill nylon - durable and long lasting.
2. Fits all S&W M&P full size and compact size pistols.
(Does not fit compact models or pistols with thumb
safety. Blocks key safety)
3.
Weight including spirol spring pin: 0.24 oz (6.9 gram)
4. Maximum width: 1.97 “(50mm), wing width of .035" (9.0mm).
Installation:
Warning - always wear eye protection if assembly or disassembly of firearms is
required.
***Make sure the firearm is unloaded before
installation begins***
Please contact a qualified gunsmith if you are not comfortable with the
installation procedures described below,
1. Use the enclosed drive pin to drive out the original ‘trigger housing pin’.
(Picture A)
2. Slide the thumb rest over the existing trigger housing pin location.
3. Use a light hammer to tap in the replacement trigger housing pin. (Picture
B) (You can use gun oil as lubricant for the pin).
4. Adjust the replacement pin even on both sides using the enclosed drive pin.
5. Test fire at an approved shooting range to get use with the thumb rest.
************************************
2.
EasyFit
MagWell for S&W M&P pistols in 9mm and .40 S&W cal. pistols
US$24.50
(Does not
fit S&W M&P M2.0)
Features:
Improves reloading
speed by 50%
Increases magazine well opening by 58%
(58% is on improved version released on September 2014. Previous version is
49%)
Protects magazine well of firearm
Specification:
Fits Smith & Wesson M&P Pistols in 9mm and 40S&W cal. with medium and small size backstrap. (Does not fit M&P Compact; need to remove bottom edge of large backstrap for proper fit).
Made of polymer (nylon) material, durable and long lasting
Weight - 0.35 OZ (9.9 gram)
original frame tool - 0.16 OZ (4.6 gram)
weight added - 0.9 OZ (5.3 gram)
Maximum width - 1.60¨ (40.6mm)
Inside width - 1.50¨(38.1mm) - increased by 58%
Original inside width of S&W M&P magwell -0.95¨ (24.1mm)
Installation:
Note: If you are not comfortable with the installation, please
have a qualified gunsmith to do the job for you.
1.
Make sure the firearm is unloaded.
2. Remove the magazine from the gun handle.
3. Rotate the 'Frame Tool' 1/4 turn (90 degree) and pull it out (it is very
tight fit).
- picture A
4. Insert the 'Frame Insert' to replace the 'Frame Tool'.
- picture B
5. Place the U shape magwell onto the 'Frame Insert' and screw tight.
- picture C
6. Insert an empty magazine for fit testing.
7. Live fire at an approved area to get use with this new fixture.
************************************
3. EasyFit MagWell for S&W M&P pistols in 45 ACP Cal.
S&W M&P 45 ACP MagWell US$25.00
(Does not
fit S&W M&P M2.0)
Features:
Improves reloading
speed by 50%
Increases magazine well opening by 55%
Protects magazine well of firearm
Specification:
Fits Smith & Wesson M&P Pistols in 45 AC P Cal. with medium and small size backstrap. (Does not fit M&P Compact; need to remove bottom edge of large backstrap for proper fit).
Made of polymer (nylon) material, durable and long lasting
Weight - 0.28 OZ (7.9 gram)
original frame tool - 0.16 OZ (4.6 gram)
weight added - 0.12 OZ (3.3 gram)
Maximum width - 1.47¨ (37.3mm)
Inside width - 1.41¨(35.8mm) - increased by 55%
Original inside width of S&W M&P 45 ACP magwell -0.90¨ (23.0mm)
Installation:
Note: If you are not comfortable with the installation, please
have a qualified gunsmith to do the job for you.
1.
Make sure the firearm is unloaded.
2. Remove the magazine from the gun handle.
3. Rotate the 'Frame Tool' 1/4 turn (90 degree) and pull it out (it is very
tight fit).
- picture A
4. Insert the 'Frame Insert' to replace the 'Frame Tool'.
- picture B
5. Place the U shape magwell onto the 'Frame Insert' and screw tight.
- picture C
6. Insert an empty magazine for fit testing.
7. Live fire at an approved area to get use with this new fixture.
Back to:
